PRIME PHASER
An extended phaser with many stages, stereo spread and colour controls.
There is a version for bass too: PRIME BASS PHASER
What it does
PRIME PHASER is a phaser with more options: from 2 to 24 stages, a choice of waveform and diffusion. You get the swirling movement, with more control over how it sounds. BI-PHASE and the DAMP controls shape the colour further.
With BI-PHASE and the DAMP controls you shape the colour further, from soft and warm to fierce and sharp.
How to use it
- Choose 2 or 4 STAGE for a light, airy swirl.
- Choose 16 or 24 STAGE for a deep, rich phaser that pulls long through the sound.
- Set SEPARATION higher for more diffusion in the swirl.
- Switch BI-PHASE on to connect the two phase shift circuits in series, for a different colour.
Where it goes in the chain
Before the amp or before the overdrive for a rough tone, or after it for a smooth one. Always before delay and reverb.
Starting points
Light air
STAGE 4 STAGE · RATE 25 · DEPTH 50 · RESONANCE 25
A soft, airy phaser for a clean tone.
Deep rotation
STAGE 16 STAGE · RATE 20 · DEPTH 75 · RESONANCE 45 · SEPARATION 90
A slow phaser with great depth and diffusion.
In series
STAGE 8 STAGE · RATE 30 · DEPTH 70 · BI-PHASE ON
Both circuits in series, a different colour for chords.
Every setting
| Setting | Range | What it does |
|---|---|---|
| STAGE | 2 STAGE / 4 STAGE / 8 STAGE / 16 STAGE / 24 STAGE | The number of filter steps. Few steps sound airy and soft, many steps sound deep, full and heavy. |
| RATE | 0 / 1 / 2 / 3 … 1/16T / 1/32 (119 steps) | The speed of the rotation: a number from 0 to 100, or a note value such as 1/4 or 1/8D, which follows the tempo (BPM) of the memory. |
| DEPTH | 0 to 100 | How far the movement reaches. Low is subtle, high pulls the tone clearly through the frequency range. |
| RESONANCE | 0 to 100 | Feeds part of the effect back in. Higher sounds sharper and nasal, lower softer and more natural. |
| MANUAL | 0 to 100 | The center frequency at which the phaser works. Lower sounds deeper and darker, higher sounds brighter. |
| WAVEFORM | TRI / SINE | The shape of the movement. TRI moves evenly, SINE is softer and rounder at the ends. |
| SEPARATION | 0 / 15 / 30 / 45 … 165 / 180 (13 steps) | Sets the diffusion, from 0 to 180 in steps of 15. The higher the value, the more diffusion. Try steps until the spread suits you. |
| STEP RATE | OFF / 0 / 1 / 2 … 1/16T / 1/32 (120 steps) | Sets the cycle of the step function, which makes the rate and depth change in steps. Higher gives finer changes. OFF leaves the step function out. |
| BI-PHASE | OFF / ON | Sets whether the two phase shift circuits are connected in series (ON) or not (OFF). Switch it to hear the difference. |
| LOW DAMP HIGH DAMP | -100 to 0 | LOW DAMP sets the amount of feedback in the low range, HIGH DAMP in the high range. Both run from -100 to 0. Listen for what suits your tone. |
| LOW CUT HIGH CUT | LOW CUT: FLAT / 20.0Hz / 25.0Hz / 31.5Hz … 10.0kHz / 12.5kHz (30 steps) HIGH CUT: 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | LOW CUT sets the frequency from which low notes are filtered out, HIGH CUT does the same for high notes. FLAT turns the filter off. |
| EFFECT LEVEL | 0 to 100 | The volume of the phaser signal in the mix. Higher gives more swirl, lower lets your own tone lead. |
| DIRECT MIX | 0 to 100 | The volume of the dry signal added to the mix. At 0 you hear mostly the effect, higher lets more of your normal tone through. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. PRIME PHASER in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Modulation
Turn it yourself?
In GX Board, PRIME PHASER is a device in your rack, with all its controls on the front.