CHORUS

Doubles your sound with a slightly detuned copy, so it plays wider and richer.

There is a version for bass too: BASS CHORUS

What it does

CHORUS mixes your dry signal with a copy whose pitch sways gently and slowly. The ear hears two guitars that almost, but not quite, play the same thing.

The sound gets wider, fuller and softer at the edges. With little DEPTH it stays subtle. With a lot of DEPTH it becomes a clear swirl.

How to use it

  • Set DEPTH low and RATE slow for a clean tone that sounds wider without wobbling.
  • Use STEREO or DUAL on chord parts so left and right sound slightly different.
  • Put it before a delay or reverb to give a solo more space.
  • Set a fast RATE with high DEPTH for a clear, watery swirl.

Where it goes in the chain

Usually after the amp or after a clean tone, and before delay and reverb. That way the echoes get wide too.

Starting points

Wide clean

TYPE STEREO · RATE 35 · DEPTH 40 · EFFECT LEVEL 75

A calm swirl that widens a clean tone without drawing attention.

Deep swirl

TYPE STEREO · RATE 60 · DEPTH 80 · WAVEFORM SINE

Clearly audible with a deeper movement, good for open chords.

Dark and soft

TYPE MONO · RATE 20 · DEPTH 50 · HIGH CUT 3.15kHz

A warm, slightly muted swirl that stays behind the tone.

Every setting

SettingRangeWhat it does
TYPEMONO / DIR/EFX / STEREO / DUALMONO: same sound left and right. DIR/EFX: dry sound left, effect right. STEREO: a different chorus on each side. DUAL: set each side on its own.
DIRECT LEVEL0 to 100The volume of the dry signal. At 100 you hear your normal tone in full. At 0 the dry signal is cut and you hear only the effect.
RATE
1: RATE
2: RATE
0 / 1 / 2 / 3 … 1/16T / 1/32 (119 steps)The speed of the swirl: a number from 0 to 100, or a note value such as 1/4 or 1/8D, which follows the tempo (BPM). In DUAL you set each voice separately.
DEPTH
1: DEPTH
2: DEPTH
0 to 100How deep the swirl is. Low is subtle and wide, high is obvious and a bit seasick. At 0 you get a doubling effect instead of a swirl. Start around 30 to 50.
EFFECT LEVEL
1: EFFECT LEVEL
2: EFFECT LEVEL
0 to 100The volume of the chorus signal in the mix. Higher gives more swirl, lower lets your own tone lead.
PRE-DELAY
1: PRE-DELAY
2: PRE-DELAY
0.0ms / 0.5ms / 1.0ms / 1.5ms … 39.5ms / 40.0ms (81 steps)The time between the dry sound and the effect sound. Short sounds tight. Longer makes it sound as if two guitars play at once (doubling).
WAVEFORM
1: WAVEFORM
2: WAVEFORM
TRI / SINETRI gives the typical chorus sound. SINE gives a deeper sense of movement.
LOW CUT
1: LOW CUT
2: LOW CUT
FLAT / 20.0Hz / 25.0Hz / 31.5Hz … 10.0kHz / 12.5kHz (30 steps)Sets the frequency from which low notes are filtered out. Higher keeps the low end tight, FLAT lets everything through.
HIGH CUT
1: HIGH CUT
2: HIGH CUT
20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps)Sets the frequency from which high notes are filtered out. Lower sounds darker and warmer, FLAT lets everything through.
OUTPUT MODEMONO / STEREOMONO suits a mono output. STEREO gives a richer sense of space on a stereo output, such as two amps or a stereo system.

The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. CHORUS in the BOSS Parameter Guide · GX-100 manuals at BOSS

Turn it yourself?

In GX Board, CHORUS is a device in your rack, with all its controls on the front.

Download for Mac