SHIMMER DELAY
An echo with a pitch-shifted sound mixed in.
What it does
SHIMMER DELAY is an echo with a pitch shift. The repeats sound higher or lower than what you play; by default an octave up.
The shifted sound is mixed into the delay, which gives a glittering tail.
How to use it
- Set PITCH to 12 and play slowly for a glittering cloud above long chords.
- Set PITCH to -12 for dark, deep repeats under your playing.
- Raise PITCH FEEDBACK slowly and listen to how the repeats build up.
- Keep EFFECT LEVEL low in a band, so the shimmer does not fill the mix.
Where it goes in the chain
After the amp, before the reverb. The shifted echo then sounds clear and the reverb gives it room around it.
Starting points
Glitter cloud
TIME 500ms · FEEDBACK 50 · EFFECT LEVEL 35 · PITCH 12 · PITCH BALANCE 100 · PITCH FEEDBACK 60
A cloud of higher repeats above long chords.
Deep echo
TIME 450ms · FEEDBACK 40 · EFFECT LEVEL 35 · PITCH -12 · PITCH BALANCE 60
Repeats an octave lower that make your playing darker and bigger.
Soft glow
TIME 350ms · FEEDBACK 30 · EFFECT LEVEL 25 · PITCH 12 · PITCH BALANCE 50 · HIGH CUT 5.00kHz
A light glow that adds to the plain echo without standing out.
Every setting
| Setting | Range | What it does |
|---|---|---|
| TIME | 1ms / 2ms / 3ms / 4ms … 1/1D / 2/1 (2018 steps) | The time between repeats, in milliseconds or as a note value such as 1/4 or 1/8D. A note value follows the tempo (BPM) of the memory. |
| FEEDBACK | 0 to 100 | How much of the echo comes back. Low gives a few repeats, high a long tail. |
| EFFECT LEVEL | 0 to 120 | The volume of the echoes. Start low, around 30, because the shifted tones stand out quickly. |
| DIRECT LEVEL | 0 to 100 | The volume of your dry signal. At 100 your guitar stays as it was. |
| HIGH CUT | 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | Cuts the high end of the echoes. Lower softens the shimmer, FLAT lets everything through. |
| MOD RATE MOD DEPTH | 0 to 100 | Makes the echoes waver lightly. RATE is the speed, DEPTH the amount. At DEPTH 0 you hear nothing. |
| DUCK SENS | 0 to 100 | How sensitive the ducking is to your playing. Higher means the echo steps back sooner. |
| DUCK PRE | 0 to 100 | Turns down the signal going into the echo while you play loudly. Closer to 100 gives a stronger reduction. |
| DUCK POST | 0 to 100 | Turns down the output of the echo while you play loudly. Closer to 100 gives a deeper reduction. |
| PITCH | -24 to 24 | How much higher or lower the repeats sound, in semitones. 12 is an octave up, -12 an octave down, 0 no shift. |
| PITCH BALANCE | 0 to 100 | The balance between the pitch-shifted signal that feeds the echo and your direct signal. Raise it for more shifted sound in the echoes. |
| PITCH FEEDBACK not verified | 0 to 100 | Sets how much delay feedback is applied to the direct sound. Raise it slowly and listen to how the shifted repeats build up. |
| CARRYOVER | OFF / ON | ON lets the echoes ring out after you switch the effect off. OFF cuts them off at once. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. SHIMMER DELAY in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Echo
Turn it yourself?
In GX Board, SHIMMER DELAY is a device in your rack, with all its controls on the front.