DELAY PLUS
An echo with several stereo types, modulation, ducking and a dual version.
What it does
DELAY PLUS is an extended echo. You choose mono, stereo, pan, reverse or two echoes side by side.
You can make the repeats drift with modulation and let them duck while you play. Your playing stays clear, and the echo comes back when you stop.
How to use it
- Choose PAN for echoes that bounce between left and right.
- Choose REVERSE for repeats that sound backwards, lovely under long chords.
- Raise DUCK SENS and DUCK POST for an echo that steps back while you play and returns in the gaps.
- Choose DUAL for two echoes with their own time, such as a short one and a long one that form a rhythm together.
Where it goes in the chain
After the amp or at the end of the chain, like any echo. In a stereo setup the PAN and STEREO types come out best.
Starting points
Ping-pong
TYPE PAN · TIME 1/8D · FEEDBACK 40 · EFFECT LEVEL 45
Echoes that bounce between left and right in a dotted rhythm.
Ducking echo
TYPE MONO · TIME 500ms · FEEDBACK 40 · DUCK SENS 60 · DUCK POST 60
The echo stays quiet while you play and fills the gaps afterwards.
Two echoes
TYPE DUAL · MODE L/R · 1: TIME 1/4 · 2: TIME 1/8D · 1: TYPE ANALOG · 2: TYPE TAPE
A short and a long echo, left and right, forming a rhythm together.
Every setting
| Setting | Range | What it does |
|---|---|---|
| TYPE | MONO / DIR/EFX / STEREO / PAN / REVERSE / DUAL | The kind of echo. MONO is plain, DIR/EFX splits your dry signal from the echo, STEREO and PAN spread over left and right, REVERSE turns the repeats around, DUAL uses two echoes. |
| TIME | 1ms / 2ms / 3ms / 4ms … 1/1D / 2/1 (2018 steps) | The time between repeats, in milliseconds or as a note value such as 1/4 or 1/8D. A note value follows the tempo (BPM) of the memory. |
| FEEDBACK | 0 to 100 | How much of the echo comes back. Low gives a few repeats, high a long tail. |
| EFFECT LEVEL | 0 to 120 | The volume of the echoes. Start low and raise it until you just hear them. |
| DIRECT LEVEL | 0 to 100 | The volume of your dry signal. At 100 your guitar stays as it was. |
| HIGH CUT | 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | Cuts the high end of the echoes. Lower gives darker repeats, FLAT lets everything through. |
| MOD RATE MOD DEPTH | 0 to 100 | Makes the echoes drift slightly. RATE is the speed, DEPTH the amount. At DEPTH 0 you hear nothing; small values give a soft, living echo. |
| DUCK SENS | 0 to 100 | How sensitive the ducking is to your playing. Higher means the echo steps back sooner, even when you play softly. |
| DUCK PRE | 0 to 100 | Turns down the signal going into the echo while you play loudly. Closer to 100 gives a stronger reduction. |
| DUCK POST | 0 to 100 | Turns down the output of the echo while you play loudly. Closer to 100 gives a deeper reduction. |
| TAP TIME | 0 to 100 | Only with TYPE PAN. Sets the right echo time as a percentage of the left one. At 100 they are equal; lower gives a shorter right echo. |
| AUTO TRIGGER | OFF / ON | Only with TYPE REVERSE. ON makes the effect match what you play. |
| CARRYOVER | OFF / ON | ON lets the echoes ring out after you switch the effect off. OFF cuts them off at once. |
| MODE | SERIES / PARALLEL / L/R | With the DUAL type: SERIES puts the two echoes one after the other, PARALLEL side by side, L/R puts one left and one right. |
| 1: TYPE 2: TYPE | MONO / PAN / ANALOG / TAPE | The kind of echo 1 and echo 2 with DUAL. MONO is plain, PAN divides the time between left and right, ANALOG sounds mild and analog, TAPE has the wavering sound of a tape echo. |
| 1: TIME 2: TIME | 1ms / 2ms / 3ms / 4ms … 1/1D / 2/1 (2018 steps) | The echo time of echo 1 and echo 2. Pick different values or note values, such as 1/4 and 1/8D, for a rhythm. Note values follow the tempo of the memory. |
| 1: FEEDBACK 2: FEEDBACK | 0 to 100 | How many repeats echo 1 and echo 2 have. Keep one lower than the other for a clear difference. |
| 1: EFFECT LEVEL 2: EFFECT LEVEL | 0 to 120 | The volume of echo 1 and echo 2. Set the second a bit softer for an echo that leans on the first. |
| 1: HIGH CUT 2: HIGH CUT | 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | Cuts the high end of echo 1 and echo 2. Make the longer echo darker so it stays behind the short one. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. DELAY PLUS in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Echo
Turn it yourself?
In GX Board, DELAY PLUS is a device in your rack, with all its controls on the front.