REVERB PLUS
An extended reverb with damping, modulation and ducking.
What it does
REVERB PLUS is a reverb with extra controls. You choose the kind of space, the length and the tone, and you can make the reverb waver or duck while you play.
The dampers turn down the low or high end of the reverb. That keeps it soft or bright.
How to use it
- Choose ROOM S or ROOM L for a short, natural space around a clean sound.
- Choose HALL M with a high TIME for a big hall under long notes.
- Use LOW DAMP and HIGH DAMP to turn down the lows or highs of the reverb when it clouds your sound.
- Raise DUCK SENS and DUCK POST for a reverb that stays soft while you play and comes up when you stop.
Where it goes in the chain
Usually the last effect in the chain, after the echoes. The reverb then sits around everything you play.
Starting points
Natural room
TYPE ROOM S · TIME 0.9s · PRE-DELAY 10 · EFFECT LEVEL 25
A short, natural space for a clean sound.
Hall with ducking
TYPE HALL M · TIME 3.5s · PRE-DELAY 40 · EFFECT LEVEL 35 · DUCK SENS 60 · DUCK POST 50
A big hall that stays soft while you play and comes up in the gaps.
Waving plate
TYPE PLATE · TIME 2.5s · EFFECT LEVEL 30 · MOD RATE 30 · MOD DEPTH 20 · HIGH DAMP 15
A metallic, lightly living reverb.
Every setting
| Setting | Range | What it does |
|---|---|---|
| TYPE | HALL S / HALL M / PLATE / ROOM S / ROOM L | The kind of space. HALL S is clear and spacious, HALL M mild, PLATE metallic with bright highs, ROOM S a warm small room, ROOM L a larger room. |
| TIME | 0.1s / 0.2s / 0.3s / 0.4s … 9.9s / 10.0s (100 steps) | How long the reverb lasts. Short values give a small space, long ones a hall. For chords, 1 to 3 seconds often works well. |
| PRE-DELAY | 0 to 200 | The time between your note and the start of the reverb. Higher keeps your playing clearer and makes the space a bit bigger. |
| DENSITY | 1 to 10 | How dense the reverb is. High values sound smooth, low values let single echoes show. Choose by taste. |
| EFFECT LEVEL | 0 to 100 | The volume of the reverb. Start around 20 to 30 and raise it until you just hear the space. |
| LOW CUT HIGH CUT | LOW CUT: FLAT / 20.0Hz / 25.0Hz / 31.5Hz … 10.0kHz / 12.5kHz (30 steps) HIGH CUT: 20.0Hz / 25.0Hz / 31.5Hz / 40.0Hz … 12.5kHz / FLAT (30 steps) | Cut the low and high end of the reverb. A higher LOW CUT and lower HIGH CUT keep the reverb slim and soft, so it does not cloud your playing. |
| DIRECT LEVEL | 0 to 100 | The volume of your dry signal. At 100 your guitar stays as it was. |
| TONE | -50 to 50 | Shapes the overall tone of the reverb. Move it to either side of 0 and listen. |
| LOW DAMP HIGH DAMP | -50 to 50 | LOW DAMP turns down the low end of the reverb, HIGH DAMP the high end. Use them to keep the reverb from clouding the mix; listen and adjust. |
| MOD RATE MOD DEPTH | 0 to 100 | Makes the reverb waver lightly. RATE is the speed, DEPTH the amount. At DEPTH 0 you hear nothing; small values make the reverb livelier. |
| DUCK SENS | 0 to 100 | How sensitive the ducking is to your playing. Higher means the reverb steps back sooner. |
| DUCK PRE | 0 to 100 | Turns down the signal going into the reverb while you play loudly. Closer to 100 gives a stronger reduction. |
| DUCK POST | 0 to 100 | Turns down the output of the reverb while you play loudly. Closer to 100 gives a deeper reduction. |
| CARRYOVER | OFF / ON | ON lets the reverb ring out after you switch the effect off. OFF cuts it off at once. |
The settings were checked against the BOSS GX-100 Parameter Guide, version 2.00. This explanation was written by the makers of GX Board, not by BOSS. The official description of every setting is in the BOSS Parameter Guide. REVERB PLUS in the BOSS Parameter Guide · GX-100 manuals at BOSS
More in Reverb
Turn it yourself?
In GX Board, REVERB PLUS is a device in your rack, with all its controls on the front.